ADIADL5304高速200dB对数转换解决方案
2011-10-21
作者：ADI 公司
</a>对数转换器" title="对数转换器">对数转换器" title="对数转换器">对数转换器,具有快速响应和低噪音,正常对数斜率10 mV/dB(200 mV/decade),单电源工作的输入电流在1pA到3mA,双电源工作的输入电流可扩展至10mA,输入电流大于1uA时的带宽大于4MHz,主要用在高精度光功率测量,宽范围基带对数压缩和高速APC回路的检测.本文介绍了ADL5304主要特性,简化方框图,多种参数测量电路图以及单电源工作基本连接图,评估板电路图和PCB布局图.
The ADL5304 is a high speed logarithmic converter with fast response and low noise over a 200 dB (1 pA to 10 mA) measurement range. The ADL5304 provides a nominal logarithmic slope of 10 mV/dB (200 mV/decade); other values are easily configured. Logarithmic intercept can be programmed over a wide range with the internal 100 nA current source or externally for log ratio applications. The default intercept value of 3.162 fA places the midpoint of the measurement range of 100 nA at VLOG = 1.5 V.
A single positive supply of 5 V is all that is required for operation over a specified 1 pA to 3 mA input range. Dual-supply operation extends the specified input current range to 10 mA.
The ADL5304 accepts two current inputs to the logarithmic argument. The numerator input, INUM, flows in the collector of an NPN transistor, connected in a feedback path around a low offset JFET amplifier. The denominator current, IDEN, is treated in the same way, which allows for log ratio operation. The input summing nodes (INUM and IDEN) operate at a constant default voltage of 1.5 V. The VSM1 to VSM4 pins flank the INUM and IDEN inputs to provide a guard voltage to minimize leakage currents.
Adaptive photodiode biasing is provided for optical measurements. A monitor current 1.1 times INUM is output at the IMON pin, and an external resistor, RMNTR, at 10 times the photodiode series resistance (RS) applies a voltage across the photodiode that 1st order keeps the internal PD junction at 0 V to minimize dark current.
The VLOG output is buffered and can be rescaled through internal gain setting resistors. The internal ILOG varies from −400 μA to +400 μA as INUM changes over 10 decades from 1 pA to 10 mA. This corresponds to 0.5 V to 2.5 V at the VLOG pin in the default configuration shown in Figure 1.
Accurate 1.5 V (Pin 1P5V) and 2.0 V (Pin 2VLT) reference outputs allow precise repositioning of the intercept using external resistors.
The ADL5304 is available in a 32-lead, 5 mm × 5 mm LFCSP and specified for operation from −40°C to +85°C.
ADL5304主要特性:
Optimized for very fast response at all input currents
Overall bandwidth of >4 MHz for inputs >1 μA
Bandwidth: 25 kHz at input of 1 nA and 350 kHz at 10 nA
10 decades of input range: 1 pA to 10 mA
Law conformance: ±0.25 dB from 100 pA to 100 μA
Log ratio or fixed-intercept operation
Precision voltage references and reference current
Adaptive photodiode (PD) bias for low dark current
Programmable log slope and intercept
Default log slope of 10 mV/dB at VLOG pin
Single- or dual-supply operation
ADL5304应用:
High accuracy optical power measurement
Wide range baseband log compression
Versatile detector for high speed APC loops
图1.ADL5304简化方框图
图2.ADL5304测量对数/斜率/失调一致性电路图
图3.ADL5304测量带宽电路图
图4.ADL5304测量脉冲设定电路图
图5.ADL5304测量光电二极管脉冲响应电路图
图6.ADL5304测量输出电路图
图7.ADL5304测量IMON脉冲响应电路图
图8.ADL5304测量噪音定电路图: INUM = 100 pA, INUM = 1 nA,和INUM = 10 nA
图9.ADL5304单电源工作基本连接图
图10.ADL5304评估板电路图
图11.ADL5304评估板PCB布局图
详情请见:
http://www.analog.com/static/imported-files/data_sheets/ADL5304.pdf
The ADL5304 is a high speed logarithmic converter with fast response and low noise over a 200 dB (1 pA to 10 mA) measurement range. The ADL5304 provides a nominal logarithmic slope of 10 mV/dB (200 mV/decade); other values are easily configured. Logarithmic intercept can be programmed over a wide range with the internal 100 nA current source or externally for log ratio applications. The default intercept value of 3.162 fA places the midpoint of the measurement range of 100 nA at VLOG = 1.5 V.
A single positive supply of 5 V is all that is required for operation over a specified 1 pA to 3 mA input range. Dual-supply operation extends the specified input current range to 10 mA.
The ADL5304 accepts two current inputs to the logarithmic argument. The numerator input, INUM, flows in the collector of an NPN transistor, connected in a feedback path around a low offset JFET amplifier. The denominator current, IDEN, is treated in the same way, which allows for log ratio operation. The input summing nodes (INUM and IDEN) operate at a constant default voltage of 1.5 V. The VSM1 to VSM4 pins flank the INUM and IDEN inputs to provide a guard voltage to minimize leakage currents.
Adaptive photodiode biasing is provided for optical measurements. A monitor current 1.1 times INUM is output at the IMON pin, and an external resistor, RMNTR, at 10 times the photodiode series resistance (RS) applies a voltage across the photodiode that 1st order keeps the internal PD junction at 0 V to minimize dark current.
The VLOG output is buffered and can be rescaled through internal gain setting resistors. The internal ILOG varies from −400 μA to +400 μA as INUM changes over 10 decades from 1 pA to 10 mA. This corresponds to 0.5 V to 2.5 V at the VLOG pin in the default configuration shown in Figure 1.
Accurate 1.5 V (Pin 1P5V) and 2.0 V (Pin 2VLT) reference outputs allow precise repositioning of the intercept using external resistors.
The ADL5304 is available in a 32-lead, 5 mm × 5 mm LFCSP and specified for operation from −40°C to +85°C.
ADL5304主要特性:
Optimized for very fast response at all input currents
Overall bandwidth of >4 MHz for inputs >1 μA
Bandwidth: 25 kHz at input of 1 nA and 350 kHz at 10 nA
10 decades of input range: 1 pA to 10 mA
Law conformance: ±0.25 dB from 100 pA to 100 μA
Log ratio or fixed-intercept operation
Precision voltage references and reference current
Adaptive photodiode (PD) bias for low dark current
Programmable log slope and intercept
Default log slope of 10 mV/dB at VLOG pin
Single- or dual-supply operation
ADL5304应用:
High accuracy optical power measurement
Wide range baseband log compression
Versatile detector for high speed APC loops
图1.ADL5304简化方框图
图2.ADL5304测量对数/斜率/失调一致性电路图
图3.ADL5304测量带宽电路图
图4.ADL5304测量脉冲设定电路图
图5.ADL5304测量光电二极管脉冲响应电路图
图6.ADL5304测量输出电路图
图7.ADL5304测量IMON脉冲响应电路图
图8.ADL5304测量噪音定电路图: INUM = 100 pA, INUM = 1 nA,和INUM = 10 nA
图9.ADL5304单电源工作基本连接图
图10.ADL5304评估板电路图
图11.ADL5304评估板PCB布局图
详情请见:
http://www.analog.com/static/imported-files/data_sheets/ADL5304.pdf
本站内容除特别声明的原创文章之外，转载内容只为传递更多信息，并不代表本网站赞同其观点。转载的所有的文章、图片、音/视频文件等资料的版权归版权所有权人所有。本站采用的非本站原创文章及图片等内容无法一一联系确认版权者。如涉及作品内容、版权和其它问题，请及时通过电子邮件或电话通知我们，以便迅速采取适当措施，避免给双方造成不必要的经济损失。联系电话：010-82306118；邮箱：aet@chinaaet.com。