《电子技术应用》
您所在的位置:首页 > 其他 > 业界动态 > 利用 TI信号链解决方案加速手持终端手机设计

利用 TI信号链解决方案加速手持终端手机设计

2007-08-08
作者:TI

           

                                             手持终端信号链" title="信号链">信号链结构图

SN65LVDS30x -可编程 27 位显示屏串行接口发送器 

The SN65LVDS301 serializer device converts 27 parallel data inputs to 1, 2, or 3 Sub Low-Voltage Differential Signaling (SubLVDS) serial outputs. It loads a shift register with 24 pixel bits and 3 control bits from the parallel CMOS input interface. In addition to the 27 data bits, the device adds a parity bit and two reserved bits into a 30-bit data word. Each word is latched into the device by the pixel clock (PCLK). The parity bit (odd parity) allows a receiver to detect single bit errors. The serial shift register is uploaded at 30, 15, or 10 times the pixel-clock data rate depending on the number of serial links used. A copy of the pixel clock is output on a separate differential output. 

特性 

  • FlatLink?3G serial interface technology  
  • Compatible with FlatLink3G receivers such as SN65LVDS302  
  • Input supports 24-bit RGB video mode interface  
  • 24-Bit RGB Data, 3 Control Bits, 1 Parity Bit and 2 Reserved Bits Transmitted over 1, 2 or 3 Differential Lines  
  • SubLVDS Differential Voltage Levels  
  • Effective Data Throughput up to 1755 Mbps  
  • Three Operating Modes to Conserve Power  
    • Active-Mode QVGA 17.4 mW (typ)  
    • Active-Mode VGA 28.8 mW (typ)  
    • Shutdown Mode 0.5 μA (typ)  
    • Standby Mode 0.5 μA (typ) 
  • Bus Swap for Increased PCB Layout Flexibility  
  • 1.8-V Supply Voltage  
  • ESD Rating >: 2 kV (HBM)  
  • Typical Application: Host-Controller to Display-Module Interface  
  • Pixel Clock Range of 4 MHz-65 MHz  
  • Failsafe on all CMOS Inputs  
  • Packaging: 80 Pin 5mm × 5mm μBGA?  
  • Very low EMI meets SAE J1752/3 'M'-spec 

FlatLink is a trademark of Texas Instruments.
μBGA is a registered trademark of Tessera, Inc. 

TLV320AIC3104 -具有 6 输入、4 输出的耳机放大器与增强数字效果的低功耗" title="低功耗">低功耗立体声编解码器" title="编解码器">编解码器 

The TLV320AIC3104 is a low-power stereo audio codec with stereo headphone amplifier, as well as multiple inputs and outputs that are programmable in single-ended or fully differential configurations. Extensive register-based power control is included, enabling stereo 48-kHz DAC playback as low as 14 mW from a 3.3-V analog supply, making it ideal for portable battery-powered audio and telephony applications. 

特性 

  • Stereo Audio DAC  
    • 100-dBA Signal-to-Noise Ratio  
    • 16/20/24/32-Bit Data  
    • Supports Sample Rates From 8 kHz to 96 kHz  
    • 3D/Bass/Treble/EQ/De-Emphasis Effects  
    • Flexible Power Saving Modes and Performance are Available 
  • Stereo Audio ADC  
    • 92-dBA Signal-to-Noise Ratio  
    • Supports Sample Rates From 8 kHz to 96 kHz  
    • Digital Signal Processing and Noise Filtering Available During Record 
  • Six Audio Input Pins  
    • One Stereo Pair of Single-Ended Inputs  
    • One Stereo Pair of Fully Differential Inputs 
  • Six Audio Output Drivers  
    • Stereo Fully Differential or Single-Ended Headphone Drivers  
    • Fully Differential Stereo Line Outputs 
  • Low Power: 14-mW Stereo 48-kHz PlaybackWith 3.3-V Analog Supply  
  • Ultralow-Power Mode with Passive Analog Bypass  
  • Programmable Input/Output Analog Gains  
  • Automatic Gain Control (AGC) for Record  
  • Programmable Microphone Bias Level  
  • Programmable PLL for Flexible Clock Generation  
  • I2C Control Bus  
  • Audio Serial Data Bus Supports I2S, Left/Right-Justified, DSP, and TDM Modes  
  • Extensive Modular Power Control  
  • Power Supplies:  
    • Analog: 2.7 V-3.6 V.  
    • Digital Core: 1.525 V-1.95 V  
    • Digital I/O: 1.1 V-3.6 V 
  • Package: 5-mm × 5-mm 32-Pin QFN  
  • APPLICATIONS  
    • Digital Cameras  
    • Smart Cellular Phones  
    • PDAs  
    • Portable Computing  
    • Communication  
    • Entertainment Applications 

TLV320AIC3106 -具有 10 输入、7 输出、耳机 放大器与增强数字效果的低功耗立体声编解码器 

The TLV320AIC3106 is a low power stereo audio codec with stereo headphone amplifier, as well as multiple inputs and outputs programmable in single-ended or fully differential configurations. Extensive register- based power control is included, enabling stereo 48-kHz DAC playback as low as 15 mW from a 3.3-V analog supply, making it ideal for portable battery-powered audio and telephony applications. 

特性 

  • Stereo Audio DAC  
    • 102-dBA Signal-to-Noise Ratio  
    • 16/20/24/32-Bit Data  
    • Supports Rates From 8 kHz to 96 kHz  
    • 3D/Bass/Treble/EQ/De-Emphasis Effects  
    • Flexible Power Saving Modes and Performance are Available 
  • Stereo Audio ADC  
    • 92-dBA Signal-to-Noise Ratio  
    • Supports Rates From 8 kHz to 96 kHz  
    • Digital Signal Processing and Noise Filtering Available During Record 
  • Ten Audio Input Pins  
    • Programmable in Single-Ended or Fully Differential Configurations  
    • 3-State Capability for Floating Input Configurations 
  • Seven Audio Output Drivers  
    • Stereo Fully Differential or Single-Ended Headphone Drivers  
    • Fully Differential Stereo Line Outputs  
    • Fully Differential Mono Output 
  • Low Power: 15-mW Stereo 48-kHz PlaybackWith 3.3-V Analog Supply  
  • Ultra-Low Power Mode with Passive Analog Bypass  
  • Programmable Input/Output Analog Gains  
  • Automatic Gain Control (AGC) for Record  
  • Programmable Microphone Bias Level  
  • Programmable PLL for Flexible Clock Generation  
  • Control Bus Selectable SPI or I2C  
  • Audio Serial Data Bus Supports I2S, Left/Right-Justified, DSP, and TDM Modes  
  • Alternate Serial PCM/I2S Data Bus for Easy Connection to Bluetooth? Module  
  • Concurrent Digital Microphone and Analog Microphone Support Available  
  • Extensive Modular Power Control  
  • Power Supplies:  
    • Analog: 2.7 V-3.6 V.  
    • Digital Core: 1.525 V-1.95 V  
    • Digital I/O: 1.1 V-3.6 V 
  • Packages: 5 × 5 mm 80-VFBGA; 7 × 7 mm 48-QFN (Future Product)  
  • APPLICATIONS  
    • Digital Cameras  
    • Smart Cellular Phones 

MicroStar Junior is a trademark of Texas Instruments.
Bluetooth is a trademark of Bluetooth SIG, Inc. 

TLV320DAC32 -具有 4 输出、耳机/扬声器放大器与 3D 音效的低功耗立体声 DAC 

The TLV320DAC32 is a low power stereo audio DAC with and integrated power amplifier designed to drive stereo headphones or speakers. This device also has a pair of analog inputs which allow routing of external signals to the output amplifiers. The playback path includes a mix/mux capability from the stereo DAC and analog inputs, through programmable volume controls, to the headphone outputs. Extensive register-based power control is included, enabling stereo 96-kHz playback as low as 20mW from a 3.3-V analog supply, making it ideal for portable battery-powered audio and telephony applications. 

特性 

  • Stereo Audio DAC  
    • 95-dBA Signal-to-Noise Ratio  
    • 16/20/24/32-Bit Data  
    • Supports Rates From 8 kHz to 96 kHz  
    • 3D/Bass/Treble/EQ/De-emphasis Effects 
  • Two Audio Input Pins  
    • Allows Analog Bypass Path 
  • Four Audio Output Drivers  
    • Stereo 8- , 500-mW/Channel SpeakerDrive Capability  
    • Stereo Fully Differential or Single-Ended Headphone Drivers 
  • Low Power: 18-mW Stereo 48-kHz Playback With 3.3-V Analog Supply  
  • Programmable Input/Output Analog Gains  
  • Programmable Microphone Bias Level  
  • Headphone Jack Detection  
  • Programmable PLL for Flexible Clock Generation  
  • I2C Control Bus  
  • Audio Serial Data Bus Supports I2S, Left/Right-Justified, DSP, and TDM Modes  
  • Extensive Modular Power Control  
  • Internal Selectable LDO Allows Operation From Single 3.3-V Supply  
  • Power Supplies:  
    • Analog: 2.7 V-3.6 V.  
    • Digital Core: 1.525 V-1.95 V  
    • Digital I/O: 1.1 V-3.6 V 
  • Package: 5 × 5 mm 32-QFN 

TPA2006D1/32D1 -具有 1.8V 兼容关断电压的 1.45W 单声道免滤波 D 类音频放大器 

The TPA2006D1 is a 1.45-W high efficiency filter-free class-D audio power amplifier in a 3 mm × 3 mm QFN package that requires only three external components. The SHUTDOWN pin is fully compatible with 1.8-V logic GPIO, such as are used on low power cellular chipsets. 

特性 

  • Maximum Battery Life and Minimum Heat  
    • Efficiency With an 8- Speaker:  
      • 88% at 400 mW  
      • 80% at 100 mW 
    • 2.8-mA Quiescent Current  
    • 0.5-μA Shutdown Current 
  • Shutdown Pin has 1.8-V Compatible Thresholds  
  • Only Three External Components  
    • Optimized PWM Output Stage Eliminates LC Output Filter  
    • Internally Generated 250-kHz Switching Frequency Eliminates Capacitor and Resistor  
    • Improved PSRR (-75 dB) and Wide Supply Voltage (2.5 V to 5.5 V) Eliminates Need for a Voltage Regulator  
    • Fully Differential Design Reduces RF Rectification and Eliminates Bypass Capacitor  
    • Improved CMRR Eliminates Two Input Coupling Capacitors 
  • Space Saving 3 mm x 3 mm QFN Package (DRB)  
  • APPLICATIONS  
    • Ideal for Wireless or Cellular Handsets and PDAs 

TPA6130A2 - 100mW 耳机驱动器 

The TPA6130A2 is a stereo DirectPath? headphone amplifier with I2C digital volume control. The TPA6130A2 has minimal quiescent current consumption, with a typical IDD of 4 mA, making it optimal for portable applications. The I2C control allows maximum flexibility with a 64 step audio taper volume control, channel independent enables and mutes, and the ability to configure the outputs into stereo, dual mono, or a single receiver speaker BTL amplifier that drives 300 mW of  

特性 

  • DirectPath Ground-Referenced Outputs  
    • Eliminates Output DC Blocking Capacitors  
    • Reduces Board Area  
    • Reduces Component Height and Cost  
    • Full Bass Response Without Attenuation 
  • Power Supply Voltage Range: 2.5 V to 5.5 V  
  • 64 Step Audio Taper Volume Control  
  • High Power Supply Rejection Ratio (>100 dB PSRR)  
  • Differential Inputs for Maximum Noise Rejection (68 dB CMRR)  
  • High-Impedance Outputs When Disabled  
  • Advanced Pop and Click Suppression Circuitry  
  • Digital I2C Bus Control  
    • Per Channel Mute and Enable  
    • Software Shutdown  
    • Multi-Mode Support: Stereo HP, Dual Mono HP, and Single-Channel BTL Operation  
    • Amplifier Status 
  • Space Saving Lead-Free (Pb-Free) Packages  
    • 20 Pin, 4 mm x 4 mm QFN  
    • 16 ball, 2 mm x 2 mm WCSP 
  • ESD Protection of 8 kV HBM and IEC Contact  
  • APPLICATIONS  
    • Mobile Phones  
    • Portable Media Players  
    • Notebook Computers  
    • High Fidelity Applications 

DirectPath is a trademark of Texas Instruments. 

TPA6205A11.7W AB 类音频功率放大器 

The TPA6205A1 is a 1.25-W mono fully differential amplifierdesigned to drive a speaker with at least 8- impedance while consuming less than 37 mm2 (ZQV package option) total printed-circuit board (PCB) area in most applications. This device operates from 2.5 V to 5.5 V, drawing only 1.7 mA of quiescent supply current. The TPA6205A1 is available in the space-saving 2 mm x 2 mm MicroStar Junior? BGA package, and the space saving 3 mm x 3 mm QFN (DRB) package. 

特性 

  • 1.25 W Into 8 From a5-V Supply at THD = 1% (Typical)  
  • Shutdown Pin has 1.8V Compatible Thresholds  
  • Low Supply Current: 1.7mA Typical  
  • Shutdown Current < 10μA  
  • Only Five External Components  
    • Improved PSRR (90 dB) and Wide Supply Voltage (2.5V to 5.5V) for Direct Battery Operation  
    • Fully Differential Design Reduces RF Rectification  
    • Improved CMRR Eliminates Two Input Coupling Capacitors  
    • C(BYPASS) Is Optional Due to Fully Differential Design and High PSRR 
  • Available in 3 mm x 3 mm QFN Package (DRB)  
  • Available in an 8-Pin PowerPAD? MSOP (DGN)  
  • Avaliable in a 2 mm x 2 mm MicroStar Junior? BGA Package (ZQV)  
  • APPLICATIONS  
    • Designed for Wireless Handsets, PDAs, and other mobile devices  
    • Compatible with Low Power (1.8V Logic) I/O Threshold control signals 

PowerPAD, MicroStar Junior are trademarks of Texas Instruments. 

TSC2007 -具有 I2C 总线的 1.2V-3.6V、12 位 200KSPS 低成本、毫微瓦功耗触摸屏控制器 

The TSC2007 is a very low-power touch screen controller designed to work with power-sensitive, handheld applications that are based on an advanced low-voltage processor. It works with a supply voltage as low as 1.2V, which can be supplied by a single-cell battery. It contains a complete, ultra-low power, 12-bit, analog-to-digital (A/D) resistive touch screen converter, including drivers and the control logic to measure touch pressure. 

特性 

  • 4-Wire Touch Screen Interface  
  • Single 1.2V to 3.6V Supply/Reference  
  • Ratiometric Conversion  
  • Effective Throughput Rate:  
    • Up to 20kHz (8-Bit) or 10kHz (12-Bit) 
  • Preprocessing to Reduce Bus Activity  
  • I2C? Interface Supports:  
    • Standard, Fast, and High-Speed Modes 
  • Simple, Command-Based User Interface:  
    • TSC2003 Compatible  
    • 8- or 12-Bit Resolution 
  • On-Chip Temperature Measurement  
  • Touch Pressure Measurement  
  • Digital Buffered PENIRQ  
  • On-Chip, Programmable PENIRQ Pullup  
  • Auto Power-Down Control  
  • Low Power:  
    • 32.24μA at 1.2V, Fast Mode, 8.2kHz Eq Rate  
    • 39.31μA at 1.8V, Fast Mode, 8.2kHz Eq Rate  
    • 53.32μA at 2.7V, Fast Mode, 8.2kHz Eq Rate 
  • Enhanced ESD Protection:  
    • ±8kV HBM  
    • ±1kV CDM  
    • ±25kV Air Gap Discharge  
    • ±15kV Contact Discharge 
  • 1.5 x 2 WCSP-12 and 5 x 6.4 TSSOP-16 Packages  
  • APPLICATIONS  
    • Cellular Phones  
    • PDA, GPS, and Media Players  
    • Portable Instruments  
    • Point-of-Sale Terminals  
    • Multiscreen Touch Control 

U.S. Patent NO. 6246394; other patents pending.

I2C is a trademark of NXP Semiconductors.
All other trademarks are the property of their respective owners. 

本站内容除特别声明的原创文章之外,转载内容只为传递更多信息,并不代表本网站赞同其观点。转载的所有的文章、图片、音/视频文件等资料的版权归版权所有权人所有。本站采用的非本站原创文章及图片等内容无法一一联系确认版权者。如涉及作品内容、版权和其它问题,请及时通过电子邮件或电话通知我们,以便迅速采取适当措施,避免给双方造成不必要的经济损失。联系电话:010-82306118;邮箱:aet@chinaaet.com。