《电子技术应用》
您所在的位置:首页 > 可编程逻辑 > 设计应用 > 小型化超声激励接收仪接收电路及 FPGA 控制方法研究
小型化超声激励接收仪接收电路及 FPGA 控制方法研究
电子技术应用
邹扬翔1,吕炎1,高杰1,吕金鸽2,李杨3,杨敬4,何存富1
1.北京工业大学 信息科学技术学院;2.北京工业大学 机械与能源工程学院;3.国合通用(重庆)测试评价认证有限公司;4.北京航天测控技术有限公司
摘要: 针对高频超声显微测量中高压激励残余与微弱回波并存的问题,设计一种小型化超声激励接收仪及现场可编程门阵列控制方法。接收链路集成限幅保护、程控增益、电源管理和模式切换,现场可编程门阵列完成触发、增益配置、接收屏蔽和采样窗口协调。测试表明,限幅输出约为±1.6 V,增益范围约为-10 dB至70 dB,整机可完成50 MHz至200 MHz换能器A扫采集,并在120 MHz、4 μm步距下实现样品扫查成像。以硅通孔扫查成像结果为例进行测试,结果说明该设计可支撑高频超声显微检测中的回波保护、幅值调理和同步采集。
中图分类号:TH878;TN782 文献标志码:A DOI: 10.16157/j.issn.0258-7998.268417
中文引用格式: 邹扬翔,吕炎,高杰,等. 小型化超声激励接收仪接收电路及 FPGA 控制方法研究[J]. 电子技术应用,2026,52(11):23-29.
英文引用格式: Zou Yangxiang,Lv Yan,Gao Jie,et al. Research on the receiving circuit and FPGA control method for a miniaturized ultrasonic pulser-receiver[J]. Application of Electronic Technique,2026,52(11):23-29.
Research on the receiving circuit and FPGA control method for a miniaturized ultrasonic pulser-receiver
Zou Yangxiang1,Lv Yan1,Gao Jie1,Lv Jinge2,Li Yang3,Yang Jing4,He Cunfu1
1.School of Information Science and Technology, Beijing University of Technology;2.College of Mechanical and Energy Engineering, Beijing University of Technology;3.China United (Chongqing) Test & Certification Co., Ltd.;4.Beijing Aerospace Measurement & Control Technology Co., Ltd.
Abstract: To address the coexistence of high-voltage excitation residuals and weak echo signals in high-frequency ultrasonic microscopic measurement, a miniaturized ultrasonic pulser-receiver and a field-programmable gate array control method are designed. The receiving chain integrates limiting protection, programmable gain, power management, and mode switching. The field-programmable gate array is used to coordinate triggering, gain configuration, receiver blanking, and sampling window control. Test results show that the limiting output is approximately ±1.6 V, the gain range is approximately -10 dB to 70 dB, and the system can perform A-scan acquisition using transducers from 50 MHz to 200 MHz. In addition, sample scanning imaging is achieved with a 120 MHz transducer and a scanning step of 4 μm. The results indicate that the proposed design can support echo protection, amplitude conditioning, and synchronous acquisition in high-frequency ultrasonic microscopic testing.
Key words : ultrasonic microscopic measurement system;limiting protection;programmable gain;field-programmable gate array control

引言

金属材料、电子封装器件和复合材料的内部缺陷会影响服役安全与器件可靠性[1]。液固界面声反射研究表明,材料内部结构会改变超声响应特征[2]。超声显微测量可无损评价缺陷和界面质量,接收链路性能直接影响回波分析结果[3]。

高频检测中,接收端既要提取毫伏级弱回波,又要承受高压激励残余耦合带来的过压风险[4]。前期跨频带超声激励/接收仪研究表明,RH500 高频调理链路需要兼顾宽带滤波、可控增益和系统级同步控制[5]。因此,本文将问题聚焦为高压残余防护、弱回波幅值调理和 FPGA 时序协同的多约束接收链路设计。

相关研究已对 kV/MHz 高重频脉冲产生[6]和宽带程控增益放大[7]进行探索。雪崩三极管脉冲发生器[8]和有源低通滤波器研究[9]也为高频激励、滤波电路提供参考。但这些工作多针对局部功能模块,尚难直接解决小型化超声显微平台中保护、增益、供电和时序协同的问题。

本文在上述工作的基础上设计小型化超声激励接收仪,将限幅保护、程控增益、电源管理、模式切换和滤波功能纳入同一硬件平台,并由现场可编程门阵列(Field Programmable Gate Array, FPGA)完成参数解析、增益配置、触发控制和状态反馈。本文重点在于面向百兆赫兹超声显微场景的多约束协同设计,为 A 扫采集和扫查成像提供硬件基础。


本文详细内容请下载:

https://www.chinaaet.com/resource/share/2000007342


作者信息:

邹扬翔1,吕炎1,高杰1,吕金鸽2,李杨3,杨敬4,何存富1

(1.北京工业大学 信息科学技术学院,北京 100124;

2.北京工业大学 机械与能源工程学院,北京 100124;

3.国合通用(重庆)测试评价认证有限公司,重庆 401122;

4.北京航天测控技术有限公司,北京 100041)

2.jpg

此内容为AET网站原创,未经授权禁止转载。